Truck Options

1.HYDRAULIC OPERATED STEEL TOP DOORS

Two (2) hydraulically operated bi-fold steel top doors with hex brake for rigidity. Doors are insulated with 2” of high temperature insulation in a double steel jacket. The doors have rain seal caps and flex plates to keep asphalt out of door hinges. Each door shall have a 1 1/2” bore with 13” stroke hydraulic cylinder with bypass and flow control valves. The controls for doors are at the front of the unit behind truck cab passenger side.

With 12 VDC in-cab door controls

2.SECONDARY AUGER MOTOR

A secondary, hydraulic, 13,000 in.lb. Torque, variable speed booster motor installed at rear of auger to assist in dispensing bad or stiff asphalt mix. This also eliminates shearing coupler keys and bolts in the auger shaft.

3.DUAL AUGER CONVEYOR SYSTEM

Two (2) each, 10’ Long by 6” diameter progressive screw conveyors, to reduce asphalt bridging has hard surfaced flights, welded continuously on 2” schedule 80 steel pipe and is ball bearing mounted. Conveyors are driven by two (2) each 13,000 in lbs of torque variable speed hydraulic motors fully synchronized with forward and reverse. Unit shall have a delivery chute with 120° of pivot. All bearings can be greased from ground level through feeder lines.

4.ASPHALT SPREADER DELIVERY SYSTEM

The asphalt spreader is hydraulic powered, ball bearing mounted 160º pivot, mounted on the rear of the main hopper auger dispensing system. Has a 52”X6” flight auger with splitter value allowing separate speed control from hopper screw conveyor and spreader auger conveyor. The conveyor is fully enclosed with releasing agent auger cleaning ports for safety. This system eliminates asphalt build up on asphalt chutes and is only recommended for large and long utility cuts.

5.ASPHALT SPREADER REMOTE CONTROL

The remote control asphalt spreader is hydraulic powered, gear driven ball bearing mounted 160º pivot, mounted on the rear of the main hopper auger dispensing system. Has a 52”X6” flight auger with splitter value allowing separate speed control from hopper screw conveyor and spreader auger conveyor. The conveyor is fully enclosed with releasing agent auger cleaning ports for safety. This system eliminates asphalt build up on asphalt chutes and is only recommended for large and long utility cuts.

6. SPOILS BIN

30” or 36” wide gravity dump asphalt spoils bin allows spoils to loaded or discharged from both sides of the truck.

30” wide, 1.25 cubic yard capacity

30” wide, .75 cubic yard capacity

36” wide, 1.5 cubic yard capacity

8.HYDRAULIC DUMP SPOILS BIN

1.50 cubic yard

2 cubic yard

9.STANLEY VIBRATORY COMPACTOR PLATE

Model SFP1850 Equipped with 5.5 hp gasoline Honda Engine with auto oil alarm shut down. Operating weight 220#, centrifugal force 4000#, plate size is 20” x 23”, water tank and locking holding down brackets.

10.VIBRATORY COMPACTOR PLATE

A Wacker WP 1550AW Compactor equipped with a 5.5 hp gasoline Honda Engine with auto oil alarm shut down. Operating weight is 196#, centrifugal force 3375#, plate size 19.5 x 23”, a water tank and locking holding down brackets.

Dolly Attachment Part No. – 0162986

11.VIBRATORY COMPACTOR PLATE

Wacker Neuson BPU2450A Reversible Vibratory Plate, weight 309lbs, centrifugal force 5,625lbs, Honda GX169 engine.

12.VIBRATORY ROLLER

The vibratory roller is a Bomag BW55 E with a 4 hp Honda Engine, operating weight of 351#, centrifugal force 2250# and single drum vibratory roller 22” wide, centrifugal clutch and water tank.

Doosan Infracore Model SX1704-595 LB Single Drum Vibratory Roller

13.HYDRAULIC REAR LIFT PLATFORM FOR COMPACTOR

A hydraulically operated lift platform for loading or unloading compactor plate. The platform has a safety latch in the up position, an in cab “platform down” indicator light with compactor holding down brackets and a pavement breaker mount. All controls for platform are at the rear of the unit.

Additional cost for platform mounted on driver’s side

With Pavement Breaker Mount

Rear Lift for 600 LB Roller 

14.HYDRAULIC REAR LIFT FOR ROLLER

A hydraulically operated lift platform for loading or unloading Bomag vibratory roller. The platform has a safety latch in the up position, an in cab “platform down” indicator light with roller hold down brackets and a pavement breaker mount. All controls for platform are at the rear of the unit.

Please specify: Driver’s side mounted or Passenger side mounted.

With Pavement Breaker Mount

With Auto Return

15.ELECTRIC HOIST

A 12 volt 1 1/3 hp electric hoist is available for loading or unloading the vibratory compactor plate.

16.PAVEMENT BREAKERS

Stanley Pavement Breaker, complete with quick couplers, asphalt cutter with lockable transporting bracket.

A. BR45 lb. Hydraulic Hammer

B. BR67 lb. Hydraulic Hammer

Tamper and detachable shank

17.HYDRAULIC TOOL LINE HOSE REEL

Shall be 3000 PSI with dual 25’ hydraulic tool lines. Reel is spring loaded auto-retractable.

Hydraulic Tool Line Hose Reel with Reel Cover

18.INSULATED TARP TOP COVER

The tarp is a double form fitted 2” insulated tarp with tie downs. The tarp material is capable of sustaining 500 degrees F.

19.DIESEL FUEL HOSE REEL

Hose reel for diesel fuel spray wand has 20’ of hose. Reel is spring loaded auto-retractable.

20.TACK OIL HOSE REEL

Hose reel for tack oil has 15’ of hose. Reel is spring loaded auto-retractable.

Dual Feed Hose Reel, Air and Tack

21.AIR LINE HOSE REEL

An airline hose reel with 20’ of hose. Reel is spring loaded auto-retractable. 

22.HYDRAULIC AIR COMPRESSOR

A separate self-contained 25 or 35 CFM @ 125 PSI. 1200 RPM hydraulic driven air compressor with 60 PSI oil pump and cooling fan, used to blow out repair sight and other compressed air demands. Hydraulic and electric controls are located at right rear of unit. Air compressor comes with quick couplers, 20 foot air hose, 5 foot air blow gun with deadman control valve, 5 gallon air tank with cable assisted condensation drain and 150 psi relief valve.

19 Gallon Air Received Tank

25 CFM @ 125 PSI compressor with 5 gallon air tank

35 CFM @ 125 PSI Compressor with 5 Gallon air tank

80 PSI Protector Valve

23.DRIP PAN

An eight (8) gallon drip pan for waste oil combination, for flushing pump, spray wand and lines at the end of the work day, with necessary valve for draining.

24.WATER TANK

A frame mounted stainless steel ten (10) gallon tank with valve and hose. Water supply for asphalt compactor plate or vibratory roller.

25 Gallon Plastic Water Tank Mounted on Spoils Bin with 65 PSI water pump and sprayer

45 Gallon Plastic Water Tank Mounted on Spoils Bin with 65 PSI water pump and sprayer

50 Gallon Plastic Water Tank Mounted on Spoils Bin with 65 PSI water pump and sprayer

**** 26, 45 & 50 gallon not available on hydraulic driven air compressor****

25.FRAME MOUNTED LP GAS BOTTLE

A frame mounted 35 gallon or 50 gallon capacity LP Gas Bottle with quick fill connector, 10 psi regulator and fuel sight gauge.

35 Gallon LP Gas Bottle

50 Gallon LP Gas Bottle

LP Gas Hose & Auto Retractable Reel w/ 20FT of Hose

20 LB 5 Gallon LP Bottle w/ rack and 200,000 BTU Hand Torch

26.FUEL

100 lb. (25 gallon) removable propane bottle complete with 10 PSI regulator valve.

27.HANDTORCH

750,000 BTU Hand torch Power Jet 8017, Storm Proof Pilot w/ Transport Bracket

28.10-LIGHT (LED) DIRECTIONAL ARROW BOARD

The arrow board is an Able 2 with arrow flashing left, right and warning bar. The board is mounted on the rear of the patch unit with in cab controls. 

29.14-LIGHT DIRECTIONAL ARROW BOARD

State D.O.T. Approved Wanco model WSBA-14 or model WSBAL-14 (L.E.D.) 14 seal beam arrow board with arrow flashing left, right and warning bar. The board is mounted on the rear of the patch unit with in cab controls.

Wanco Model WSBA-14:

Wanco Model WSBLA-14 L.E.D. Arrow Board:

Hydraulic 2 side Arrow Board with 20 LED lights

Hydraulic 2 side Arrow Board with Center Mount Strobe with 20 LED lights

Arrow Stick Superior Signal SY900 50-LED

Wanco 30” x 60” SY990 LED Arrow Board

30. 16-LIGHT DIRECTIONAL ARROW BOARD

State D.O.T. Approved Superior Signal model SRTA16. With 16 amber (L.E.D.) lights, 32 flash patterns, 8 patterns per function. Arrow flashing left, right, and warning bar.

The board is mounted on the rear of the patch unit with in cab controls.

31.STROBE LIGHT

A pedestal mounted Meteorlight model SY2000 LED amber, 80 double flashes per minute.

32. GRILL MOUNT STROBE LIGHT

Superior Signal SS-SYLED04-AA, LED Amber or White 4” Front Grill Strobe Lights, 22 flash patterns.

33. TRUCKLITE RECTANGLE 6.5” OVAL TAIL LIGHTS

LED RED, CLEAR, AMBER, & STROBE tail lights

34.WORK LIGHTS

Three (3) each 5" LED Flood Work Lights; Two (2) Rear Mount & One (1) Mount to light up inside of Hopper and LED Light-in Control Panel.

35.SAND SPREADER ASSEMBLY

The sand spreader replaces the asphalt chute and includes variable speed hydraulic motors with in-cab controls for sand discharge rate and spread width.

36.ASPHALT EDGER

Edger is designed to repair deteriorated shoulders on roads and repair water cuts and long trenches. Screw conveyor assembly is ball bearing mounted, conveyor is driven by a hydraulic motor with forward and reverse capabilities. Edger is powered with PTO driven load sense hydraulic pump. Unit mounts to rear of patch unit with 4 bolts. Has separate asphalt chute. Hydraulic splitter valve allows separate control from hopper screw conveyor to side deliver screw conveyor. Screw conveyor is fully enclosed for safety.

37.HARD SURFACED AUGERS

3/16” Hard Surfaced Auger 6”x10’

3/8” Hard Surfaced Auger 6”x10’


38.PTO

A Muncie or Chelsea PTO Hot Shift with over speed control.

Hot Shift 280 series (or equivalent):

Hot Shift CS6 series (or equivalent): For Allison 2000 Series Transmission

Muncie TG Series Electric over Air shift (or equivalent) when applicable

All Electric Units – Constant mesh PTO with Direct Mount Load Sense Pump

All Electric Units – Crankshaft Driven Front Mount Load Sense Pump

LP Gas Units- Crankshaft Driven Front Mount Load Sense Pump

39.THROTTLE CONTROL

An electronic engine throttle control remote rear mounted.

40.THROTTLE CONTROL FOR MANUAL ENGINES

Muncie Hydro-Throttle with rear manual over-ride cable.

41.FIRE EXTINGUISHERS

ABC fire extinguisher mounted on patch unit with vehicle mounting bracket.

5 Lb. In-cab mounted extinguisher

10 Lb. External mounted extinguisher

20 Lb. External mounted extinguisher

42.HIGHWAY WARNING TRIANGLES

A Highway warning triangle kit consisting of three (3) reflective triangles in a storage case.

43.EXTRA TOOL BOX

A 12 gauge steel 19” x 24” x 30” with water proof locking door.

44.WORK DECK

Available on units with a built-on road oil tank, the work deck is constructed of 1/4” angle iron and 3/16” expanded metal with assist hand rails and shall be mounted between hopper and truck cab. Deck provides easy and safe access to emulsion oil tank and asphalt hopper.

18” Wide work deck:

22” Wide work deck

24” Wide work deck:

45.ASPHALT LUTE AND SHOVEL HOLDER

Spring loaded asphalt lute and shovel holder, mounted curb side of unit.

46. SHOVEL CLEANER HOLDER

12”X12”X14” 11Guage Steel w/ 1” Drain with Fold Down Lid, Holds 3 Shovels, and Rear Mounted. 

47.SHOVELING APRON

Apron is constructed of 3/16” steel with fixed or folding bottom, mounted on platform below asphalt dispenser.

Apron with fixed bottom

Apron with hinged, folding bottom:

Extended Shoveling Apron w/ Hinged Folding Bottom

48.LIQUID ASPHALT OIL TANK BURNER ONLY REQUIRED W/ CUT BACK ROAD OIL

To enable units to work emulsion or asphalt cut back oils, tank is equipped with a dry radiant chamber with a 75,000 BTU LP gas retort tube burner regulated @ 10 psi, thermostat controlled, and 12 volt dc electronic igniter with safety shut-off on loss of flame or excessive temperature.

49.TRAFFIC CONE RACK

Set of two (2) frame mounted traffic cone racks with holding capacity of ten (10) 28” tall cones.

50.ASPHALT LUTE

36” wide aluminum asphalt lute with 7 ft. handle.

51.ASPHALT SAW

Stanley C025-541 hydraulic hand held cut off and asphalt saw.

52. WATER COOLER

Water Cooler and Rack – 3 gallon

Water Cooler and Rack – 5 gallon

53. BACKUP CAMERA

Backup Camera RVS-770613 – Kit1 Color w/ audio sound

Backup Camera RVS-770613 – Kit1 Color w/ audio sound and Mobile Mule 5500 Mobile DVR on-board recording with Two (2) 128 GB SD Cards (256 GB Total) with GPS Capabilities.

54. ASPHALT HEAT RISER PLATES

Asphalt Heat Riser Plates US Patent Pending, two thermostat controlled, low density heat riser plates that run parallel in the upper part of the asphalt hopper to keep the asphalt hot and eliminate bridging.

55. UNDERCOATING

3M brand Body Schutz 8864

56. EXTENDED SCREW CONVEYOR

12” extension of screw conveyor and rear bearing mount bracket. Allows the asphalt to be dispensed an additional 12” from asphalt hopper.

57. COST TO HARD SURFACE SCREW CONVEYOR

Hard Surfaced Screw Conveyor has hard wired bead welded on flight of auger to enhance longevity.

58. CONSPICUITY TAPE

Conspicuity tape on sides and rear of unit.


59. CUSTOM OPTIONS AVAILABLE

Option Asphalt Tack Oil Material

1. PHPM-50 TACK OIL

Biodegradable tack oil, heat range spraying temperature 45º F to 85º F, and can be stored in tank 6 to 8 months without oil separation.

PHPM-50// 275 Gallon Tote

2. BANANA SLIDE RELEASING AGENT

Biodegradable releasing agent that works like diesel.

Banana Slide 5 Gallon Bucket

Banana Slide 55 Gallon Drum

Banana Slide 275 Gallon Tote